Tungaloy ceramic cutting tools at interrupted machining

Autor: Čep, Robert
Matična publikacija: Engineering review (Technical Faculty University of Rijeka) (2012)

Chip formation analysis during hard turning

Autor: Čep, Robert
Matična publikacija: Strojarstvo (2008)

Testing of ceramic cutting tools with an interrupted cut simulator

Autor: Čep, Robert
Matična publikacija: Engineering review (Technical Faculty University of Rijeka) (2008)

Cutting tool life tests of ceramic inserts for car engine sleeves

Autor: Čep, Robert
Matična publikacija: Tehnički vjesnik (Strojarski fakultet) (2011)

Experimental tool life tests of indexable inserts for stainless steel machining

Autor: Čep, Robert
Matična publikacija: Tehnički vjesnik (Strojarski fakultet) (2013)

Experimental testing of exchangeable cutting inserts cutting ability

Autor: Čep, Robert
Matična publikacija: Tehnički vjesnik (Strojarski fakultet) (2013)

Testing of Greenleaf ceramic cutting tools with an interrupted cutting

Autor: Čep, Robert
Matična publikacija: Tehnički vjesnik (Strojarski fakultet) (2011)

Electric resistance welding of austenitic and galvanized steel sheets

Autor: Hlavatý, Ivo, Hájková, Petra, Krejčí, Lucie, Čep, Robert
Matična publikacija: Tehnički vjesnik (Strojarski fakultet) (2018)

An analysis of structures occurring in weld deposit of steel S235JR+N with tungsten carbide particles and martensitic matrix

Autor: Kozák, Jindřich, Krejčí, Lucie, Hlavatý, Ivo, Samardžić, Ivan, Čep, Robert
Matična publikacija: Metalurgija (Sisak) (2019)

Properties and comparison of PVD coatings

Autor: Mrkvica, Ivan, Neslušan, Miroslav, Čep, Robert, Sléha, Vojtěch
Matična publikacija: Tehnički vjesnik (Strojarski fakultet) (2016)

The effect of feed rate on durability and wear of exchangeable cutting inserts during cutting Ni-625

Autor: Petrú, Jana, Zlámal, Tomáš, Čep, Robert, Sadílek, Marek, Stančeková, Dana
Matična publikacija: Tehnički vjesnik (Strojarski fakultet) (2017)

Evaluation of creep properties of steel P92 and its welded joint

Autor: Mohyla, Petr
Matična publikacija: Metalurgija (Sisak) (2014)

Secondary hardening of low-alloyed creep-resistant steel welds

Autor: Mohyla, Petr
Matična publikacija: Metalurgija (Sisak) (2014)

Deformations after heat treatment and their influence on cutting process

Autor: Neslušan, Miroslav
Matična publikacija: Tehnički vjesnik (Strojarski fakultet) (2011)

Heat distribution when nickel alloy grinding

Autor: Neslušan, Miroslav
Matična publikacija: Tehnički vjesnik (Strojarski fakultet) (2012)

Influence of cutting parameters on heat-affected zone after laser cutting

Autor: Petrú, Jana
Matična publikacija: Tehnički vjesnik (Strojarski fakultet) (2013)

Testing ceramics inserts at irregular interrupted cut on material 14MoV6

Autor: Čep, Robert, Kyncl, Ladislav, Malotová, Šárka, Petrú, Jana, Zlámal, Tomáš, Czan, Andrej
Matična publikacija: Engineering review (Technical Faculty University of Rijeka) (2017)

Experimental investigation into wear and tool life of milling cutter PVD coated carbide inserts while Armox 500 steel hard milling

Autor: Majerík, Jozef, Dubovská, Rozmarína, Jambor, Jaroslav, Čep, Robert, Kratochvil, Jiří, inženjer strojarstva, Kouřil, Karel
Matična publikacija: Tehnički vjesnik (Strojarski fakultet) (2018)

Artificial neural network for predicting values of residuary resistance per unit weight of displacement

Autor: Baressi Šegota, Sandi, Anđelić, Nikola, inženjer strojarstva, Kudláček, Jan, Čep, Robert
Matična publikacija: Pomorski zbornik (2019)

Detection of grinding burn through the high and low frequency Barkhausen noise

Autor: Mičietova, Anna, Neslušan, Miroslav, Čep, Robert, Ochodek, Vladislav, Mičieta, Branislav, Pagáč, Marek
Matična publikacija: Tehnički vjesnik (Strojarski fakultet) (2017)